Technical Problems: Difference between revisions

From ECGpedia
Jump to navigation Jump to search
 
(28 intermediate revisions by 6 users not shown)
Line 4: Line 4:
|supervisor=  
|supervisor=  
}}
}}
<div style="clear:both"></div>
==Lead reversals==
==Lead reversals==
[[Image:cableReversal1.png|thumb|Right and left arm lead reversal can be distinguished from the (much rarer) dextrocardia by looking at the precordial R wave progression.]]
{{multiple image
[[Image:cableReversal2.png|thumb|Right arm and left leg lead reversal. Lead II now measures the signal between the left and right leg, which is remote from the heart.]]
| align    = right
[[Image:dextrocardia.jpg|thumb|A patient with dextrocardia (and previous inferior myocardial infarction)]]
| direction = vertical
Sometimes an ECG is not made properly. Mistakes do happen and leads can be switched. Always remain careful to check this or you might come to the wrong conclusions. One of the most common mistakes is to switch the right and left arm. This will result in negative complexes in I, indicating a right axis deviation!
| width    = 200


Common mistakes are reversal of:
| image1    = E000566.jpg
*right leg and right arm:
| caption1  = A Normal ECG
**Hardly any signal in lead II.
 
*right and left arm electrodes;
| image2    = E000567.jpg
| caption2  = right arm - right leg reversal
 
| image3    = E000563.jpg
| caption3  = left arm - left leg reversal
 
| image4    = E000564.jpg
| caption4  = left leg - right leg reversal.
 
| image5    = E000568.jpg
| caption5  = v3 - v2 reversal
 
| image6    = E000565.jpg
| caption6  = left - right reversal
}}
Lead switches are a common mistake when ECGs are made and can lead to wrong diagnoses. Common mistakes are:
* '''Left-right arm reversals''' lead to a negative complex in lead I with  a negative P wave in lead I. They are one of the most common causes of right axis deviation on the ECG!
* '''Arm-foot switches''' lead to a very small or 'far field' signal in leads II or III.
* '''Chest lead reversals''' lead to inappropriate R wave progression (increase-decrease-increase) and are often easily recognized.
Therefore '''any right axis or small signal in an extremity lead''' should be reason enough to check lead positioning. A previous ECG can be very helpful.
 
More specific patterns with every lead reversal:
*right and left arm electrodes:
**inversion of lead I
**reversal of leads II and III
**reversal of leads II and III
**reversal of leads aVR and aVL
**reversal of leads aVR and aVL
*right leg and right arm:
**diminished signal in lead II
*left arm and left leg:
*left arm and left leg:
**reversal of leads I and II
**reversal of leads I and II
**reversal of leads aVR and aVF
**reversal of leads aVL and aVF
**inversion of lead III
**inversion of lead III
*right arm and left leg:
*right arm and left leg:
**inversion of leads I, II and III
**inversion of leads I, II and III
**reversal of leads aVR and aVF
**reversal of leads aVR and aVF


It is possible to distinguish lead reversal and [[w:Dextrocardia|dextrocardia]] by watching the precordial leads. Dextrocardia will not show any R wave progression in leads V1-V6, whereas lead reversal will.
It is possible to distinguish lead reversal and [[w:Dextrocardia|dextrocardia]] by watching the precordial leads. Dextrocardia will not show any R wave progression in leads V1-V6, whereas lead reversal will.
{{clr}}


==artifacts==
<gallery>
<gallery>
Image:Noise_move.png| Movement artifacts
Image:cableReversal1.png|Right and left arm lead reversal can be distinguished from the (much rarer) dextrocardia by examination of the precordial R wave progression.
Image:ECG_Parkinson.png| Increasing movement artifacts in a Parkinson patient. The patient was in sinus rhythm! (which doesn't show on this short recording)
Image:cableReversal2.png|Right arm and left leg lead reversal. Lead II now measures the signal between the left and right leg, which is remote from the heart.
Image:BaselineDrift.png| Baseline drift. The amplifier in the ECG machine has to re-find the 'mean'. This often occurs right after lead connection and after electric cardioversion.
Image:dextrocardia.jpg|A patient with dextrocardia (and previous inferior myocardial infarction)
Image:cardioversion_from_afib.jpg| Cardioversion from atrial fibrillation to sinus rhythm, with clear baseline drift.
Image:Situs_inversus.jpg|Another patient with dextrocardia
Image:electric_noise_ecg.png| Electrical interference from a nearby electrical appliance. A typical example is a 100 Hz background distortion from fluorescent lights. Not to be confused with [[AF|atrial fibrillation]].
Image:electric_noise_ecg2.jpg| Another example of an artefact caused by an electrical appliance. The patients rhythm is regular. This strip shows 10 QRS complexes.
</gallery>
</gallery>
{{clr}}


artifacts (disturbances) can have many causes. Common causes are:
==Artifacts==
*Movement  
Artifacts (disturbances) can have many causes. Common causes are:
*Electrical interference
* Movement  
* Electrical interference
 
==Filter settings==
Although not a technical problem, filter settings influence the interpretation of the ECG.<cite>Garcia</cite>
[[File:Filter_settings.png|thumb|Filter settings can influence the interpretation of ST elevation as these examples show. On the left side an ECG with normal settigns (0.01-40Hz), on the right side a rhythm strip from the same patient with a different high-pass filter setting (0.32-40Hz). Also, the P wave morphology is different between the two ECGs.]]
To reduce electrical interference ECG machine use two filters:
* A high-pass filter reduces low frequency noise. This filter reduces base line drift on the ECG.
* A low-pass filter reduces high frequency noise, such as produces by chest and extremity muscles and electrical interference from the power grid.
 
Depending on the purpose of the ECG these filters can be adjusted.
* In the '''monitor mode''' the high-pass filter can be set higher at 0.5-1.0 Hz and the low-pass filter on 40 Hz. This is the strongest filter setting (only a narrow frequency range is passed by the filter). This setting is especially useful for rhythm monitoring where noise can be distracting and ST segment interpretation is not very important. In this mode, pacemakerspikes are sometimes invisible while filtered out.
* In the '''diagnostic mode''' the high-pass filter is set at 0.05 Hz and the low-pass filter at 40, 100 or 150 Hz. This improves the diagnostic accuracy of the ST semgent. On the downside a base line drift occurs more easily.
 
 
<gallery perRow="4">
Image:Noise_move.png|Movement artifacts
Image:ECG_Parkinson.png|Increasing movement artifacts in a Parkinson's patient. The patient was in sinus rhythm (which doesn't show on this short recording)!
Image:BaselineDrift.png|Baseline drift. The amplifier in the ECG machine has to re-find the 'mean'. This often occurs right after lead connection and after electric cardioversion.
Image:cardioversion_from_afib.jpg|Cardioversion from atrial fibrillation to sinus rhythm, with clear baseline drift.
Image:electric_noise_ecg.png|Electrical interference from a nearby electrical appliance. A typical example is a 100 Hz background distortion from fluorescent lights. Not to be confused with [[Atrial_Fibrillation|atrial fibrillation]].
Image:electric_noise_ecg2.jpg|Another example of an artifact caused by an electrical appliance. The patients rhythm is regular. This strip shows 10 QRS complexes.
File:DVA2162.jpg|An artifact that was originally diagnosed as a VT
</gallery>


{{clr}}
{{clr}}
==References==
<biblio>
#Garcia pmid=19804517
</biblio>

Latest revision as of 18:57, 24 April 2013

Author(s) J.S.S.G. de Jong
Moderator J.S.S.G. de Jong
Supervisor
some notes about authorship

Lead reversals

A Normal ECG
right arm - right leg reversal
left arm - left leg reversal
left leg - right leg reversal.
v3 - v2 reversal
left - right reversal

Lead switches are a common mistake when ECGs are made and can lead to wrong diagnoses. Common mistakes are:

  • Left-right arm reversals lead to a negative complex in lead I with a negative P wave in lead I. They are one of the most common causes of right axis deviation on the ECG!
  • Arm-foot switches lead to a very small or 'far field' signal in leads II or III.
  • Chest lead reversals lead to inappropriate R wave progression (increase-decrease-increase) and are often easily recognized.

Therefore any right axis or small signal in an extremity lead should be reason enough to check lead positioning. A previous ECG can be very helpful.

More specific patterns with every lead reversal:

  • right and left arm electrodes:
    • inversion of lead I
    • reversal of leads II and III
    • reversal of leads aVR and aVL
  • right leg and right arm:
    • diminished signal in lead II
  • left arm and left leg:
    • reversal of leads I and II
    • reversal of leads aVL and aVF
    • inversion of lead III
  • right arm and left leg:
    • inversion of leads I, II and III
    • reversal of leads aVR and aVF

It is possible to distinguish lead reversal and dextrocardia by watching the precordial leads. Dextrocardia will not show any R wave progression in leads V1-V6, whereas lead reversal will.


Artifacts

Artifacts (disturbances) can have many causes. Common causes are:

  • Movement
  • Electrical interference

Filter settings

Although not a technical problem, filter settings influence the interpretation of the ECG.[1]

Filter settings can influence the interpretation of ST elevation as these examples show. On the left side an ECG with normal settigns (0.01-40Hz), on the right side a rhythm strip from the same patient with a different high-pass filter setting (0.32-40Hz). Also, the P wave morphology is different between the two ECGs.

To reduce electrical interference ECG machine use two filters:

  • A high-pass filter reduces low frequency noise. This filter reduces base line drift on the ECG.
  • A low-pass filter reduces high frequency noise, such as produces by chest and extremity muscles and electrical interference from the power grid.

Depending on the purpose of the ECG these filters can be adjusted.

  • In the monitor mode the high-pass filter can be set higher at 0.5-1.0 Hz and the low-pass filter on 40 Hz. This is the strongest filter setting (only a narrow frequency range is passed by the filter). This setting is especially useful for rhythm monitoring where noise can be distracting and ST segment interpretation is not very important. In this mode, pacemakerspikes are sometimes invisible while filtered out.
  • In the diagnostic mode the high-pass filter is set at 0.05 Hz and the low-pass filter at 40, 100 or 150 Hz. This improves the diagnostic accuracy of the ST semgent. On the downside a base line drift occurs more easily.



References

  1. García-Niebla J, Llontop-García P, Valle-Racero JI, Serra-Autonell G, Batchvarov VN, and de Luna AB. Technical mistakes during the acquisition of the electrocardiogram. Ann Noninvasive Electrocardiol. 2009 Oct;14(4):389-403. DOI:10.1111/j.1542-474X.2009.00328.x | PubMed ID:19804517 | HubMed [Garcia]